Yodify Product Library
Instantly add the Standard POLYPAK Hydraulic Seal with Knife Trimmed Scraper Lips (SPP) and 50,000+ more product series to your store or catalog  
Book Your Demo and See How
or create your store

Standard POLYPAK Hydraulic Seal with Knife Trimmed Scraper Lips (SPP)

Brand: Parker Hannifin

Parker's hydraulic SPP Profile standard PolyPak® seal is a square shaped, symmetrical squeeze seal with a knife trimmed scraper lip for hydraulic rod and piston sealing.

Parker's SPP Profile Standard PolyPak® seal is a square cross-section squeeze seal with a symmetrical profile for use in either rod or piston applications in hydraulic systems.

The standard Molythane shell (seal body) provides high wear resistance and the O-ring spring energizer element functions as a spring to maintain sealing contact under low pressure.

The SPP Profile Standard PolyPak seal utilizes a scraper lip design formed by a precision trimming process. The scraper edge wipes both fluid film and contamination away from the seal.

A wide selection of sizes and alternate compounds allow this profile to match up with many hydraulic applications.

Please note: Pressure ratings shown are for predominantly dynamic applications.

Where the application is predominantly static, as is typical in Oil & Gas applications, maximum pressure ratings may be extended by a factor of 2 to 3 (or greater), assuming nominal extrusion gap and operating temperature within limits.

For assistance, please contact Parker’s application engineering team.

Pressure ranges shown are for systems without wear rings. If using wear rings, please consult Engineering Section (Section 2) of Parker's Fluid Power Seal Design Guide, Catalog EPS5370.

Energizer Spring Element Materials
  • For seals with 4615 or 4622 PolyPak shell, the standard spring energizer is a nitrile O-ring
  • For seals with 4651 PolyPak seal body, the O-spring energizer code must be specified. The standard code is "N" for nitrile O-ring
  • For seals with rubber PolyPak seal body, standard spring energizer is an O-ring from the same rubber material family as the seal body
Alternate Materials: For applications that may require an alternate material, please contact your Parker EPS representative.

Specifications

Body Material

  • EPDM, FKM, TPU, TPC-ET, XNBR, HNBR

Color

  • Black, Yellow, Orange

Fluid Compatibility

  • Water/Steam, Broad Range, Oils

Groove Width

  • 0.125 to 1.000

Industry Standards

  • None

Length Unit of Measure

  • inch

Maximum Pressure (psi)

  • 2000 to 7000

Maximum Surface Speed (m/sec)

  • 100 (0.5 m/sec)

Maximum Working Temperature (°F)

  • 400° F

Media

  • Hydraulic

Minimum Working Temperature (°F)

  • -65° F

Nominal Hardness

  • 90A, 95A, 60D

Polymer Family

  • EPDM, EPM, EPR, (Ethylene Propylene Rubber), FKM, FPM (Fluorocarbon), TPU (Polyurethane), TPC-ET (Thermoplastic CoPolyester Elastomer), NBR, XNBR (Nitrile-Butadiene, BUNA-N, Carboxylated Nitrile), HNBR, HSN (Hydrogenated Nitrile-Butadiene)

Spring Material

  • EPDM, FKM, NBR, HNBR

Thermal Application (°F)

  • Varies Depending on Material

Standard Materials (Shell or Seal Body)

  • P4615A90 Molythane®, Temp -65 / +200F, Pressure* 5000 psi, Surface speed < 1.6 ft/s
  • P4622A90 Ultrathane®, Temp -65 / +225F, Pressure* 5000 psi, Surface speed < 1.6 ft/s
  • Z4651D60 PolyMyte®, Temp -65 / +275F, Pressure* 7000 psi, Surface speed < 1.6 ft/s
  • N4263A90 Nitroxile®, Temp -20 / +275F, Pressure* 2000 psi, Surface speed < 1.6 ft/s
  • E4207A90 Ethylene Propylene, Temp -65 / +300F, Pressure* 2000 psi, Surface speed < 1.6 ft/s
  • V4266A95 FKM, Temp -5 / +400F, Pressure* 2250 psi, Surface speed < 1.6 ft/s
  • V4208A90 FKM, Temp -5 / +400F, Pressure* 2000 psi, Surface speed < 1.6 ft/s
  • N4007A95 HNBR, Temp -20 / +320F, Pressure* 2500 psi, Surface speed < 1.6 ft/s
Instantly populate your store or catalog 
CREATE YOUR SITE
or book a demo with the Yodify Team
show more